ADPS

ADJUSTABLE

DEADBAND

PRESSURE

       SWITCH         

•  UL Standard 508 Guide (NKPZ) and CSA Standard C22.2 No. 14-M Class (321106) for Pressure Operated Industrial Control Equipment.
• UL Standard 873 Guide (XAPX) and CSA Standard C22.2 No. 24 Class (481302) for Temperature Indicating and Regulating Equipment.
• CE Marked

Ambient/Media Temperature Range:

• -4ºF to 180ºF (-20ºc to 82ºC)

Ideal for jockey pumps, air compress, and fire pumps, the model ADPS is an Adjustable Deadband Pressure Switch with independent set and reset points which are adjustable throughout the entire operating range of the switch.  The minimum deadband (minimum span between set and reset points) may be obtained at any point in the operating range of the switch.  A change in pressure greater than the high setting will reposition the switch mechanism to open or close a single snap-action electrical switch.

This control device is designed for use as an operating control in applications sensing air, water, or any fluid not harmful to the pressure connection, diaphragm or nitrile pressure-sealing o-ring.  Where an operating control would result in personal injury and/or loss of property, it is the responsibility of the installer to add devices (safety, limit controls) that protect against, or systems (alarm, supervisory systems) that warn of control failure.

This device is not intended for applications in explosive environments or use with hazardous fluids.

• NEMA Type 4X Enclosure for indoor or outdoor use. (To maintain 4X rating, use appropriate Type 4 conduit hub.) 
• Forged Brass or 316S.S. Pressure Connections (1/2 HP Brass only)
• Aluminum Diecast Base with Polymer Enclosure
• Beryllium Copper Diaphragm (Stainless steel isolator diaphragm included for protection of beryllium copper diaphragm on models with stainless steel pressure connection.)
• Nitrile Pressure Sealing O-ring

Switch Contact:  Snap-Action SPDT (Form C)     

• 15 Amps @ 125/250/480 VAC         
• 22 Amps @125/250/480*     
•  1 HP @ 250 VAC*       
• 1/2 HP @ 125 VAC* 
• 1/4 HP @ 250 VAC    
•  1/8 HP @ 125 VAC                   

*Only on Model number ADPS-300-1B 1/2 HP

Model Number

Price Each

ADPS-300-1B

ADPS-300-1S

ADPS-300-2S

ADPS-600-1B

ADPS-600-1S

ADPS-600-2S

ADPS-300-1B 1/2 HP

ADPS

ADJUSTABLE

DEADBAND

SWITCH

OPEN FRAME

• Recognized component to UL Standard 508.  CSA Standard C22.2 No. 14-M Class (321106) for Pressure Operated Industrial Control Equipment.
• CSA Standard C22.2 No. 24 Class (481302) for Temperature Indicating and Regulating Equipment.
• CE Marked

Ambient/Media Temperature Range:

• -4ºF to 180ºF (-20ºC to 82ºC)

The model ADPS is an Adjustable Deadband Pressure Switch with independent set and reset points which are adjustable throughout the entire operating range of the switch.  The minimum deadband (minimum span between set and reset points) may be obtained at any point in the operating range of the switch.  A change in pressure greater than the high setting will reposition the switch mechanism to open or close a single snap-action electrical switch.

This control device is designed for use as an operating control in applications sensing air, water, or any fluid not harmful to the pressure connection, diaphragm or nitrile pressure-sealing o-ring.  Where an operating control would result in personal injury and/or loss of property, it is the responsibility of the installer to add devices (safety, limit controls) that protect against, or systems (alarm, supervisory systems) that warn of control failure.

This device is not intended for applications in explosive environments or use with hazardous fluids.

• Forged Brass or 316 S.S. Pressure Connections
• Aluminum Diecast Base
• Beryllium Copper Diaphragm (Stainless steel isolator diaphragm included for protection of beryllium copper diaphragm on models with stainless steel pressure connection.)
• Nitrile Pressure Sealing O-ring

Switch Contact:

• Snap-Action SPDT (Form C)
• 15 Amps @ 125/250/480 VAC
• 1/8 HP @ 125 VAC
• 1/4 HP @ 250 VAC

CAUTION:  Direct control of motors with HP ratings greater than the ratings shown could result in premature failure of the ADPS or significantly shorten operating life

Differential

Pressure

Switch

DPS-50

$169.99 EACH

Maximum Rated Pressure:  250 PSI

Maximum Working Pressure:  180 PSI

Pressure Connections:  Brass 1/4-18 NPT Female

The Model DPS-50 is a differential pressure switch used to monitor the difference in pressure between two pressure sources.  A change in pressure between the high and low pressure ports greater than the differential pressure setting (8-50 PSID range) will reposition the switch mechanism to open or close a single electrical circuit by means of a snap-action electrical switch.  This control device is designed for applications sensing air, water or any fluid not harmful to brass or silicone and not classified as a hazardous fluid.

This control device is designed for use only as an operating control.  Where an operating control failure would result in personal injury and/or loss of property, it is the responsibility of the installer to add devices (safety, limit controls) that protect against, or systems (alarm, supervisory systems) that warn of control failure.

Ambient Temperature Range:  -40º/180ºF (40º/82ºC)

Media Temperature Range:  32º/250ºF (0º/121ºC)

Enclosure:  NEMA Type 1 (for indoor use only) Formed sheet metal with powdercoat finish.  (Not for use in hazardous locations.)

Switch Contacts:

• Snap-Action SPDT (form C) Switch
• 22 amps @ 125/250/480 VAC

Conduit Entrance:  Opening for 1/2" conduit

Motor Rating:  120VAC, 240VAC

Horsepower: 1/2,1

AC F.L.A.:  9.8, 8.0

AC L.R.A.:  58.8 ,48.0

CAUTION:  This device is not intended for applications   in explosive environments.

Industrial Flow

Switch

IFS 1 & 2

Industrial Flow

Switch

IFS-WPS

The Model IFS is a flow switch used in liquid flow lines carrying water or any fluid not harmful to brass, stainless steel or flourosilicone, and not classified as a hazardous fluid.

This switch can serve as a way to start and stop electrically operated equipment when a flow or no flow condition occurs in a variety of applications.

This device is designed for use only as an operating control.  Where an operating control failure would result in personal injury and/or loss of property, it is the responsibility of the installer to add devices (safety, limit controls) that protect against, or systems (alarm, supervisory systems) that warn of control failure.

Usage:  For pipe sized 1" to 8"

Caution:  This device is not intended for applications in explosive environments.

• UL Guide (NKPZ) for industrial control equipment per UL Standard 508 Industrial
• UL Guide (MFHX) for heating/cooling appliance switch per UL Standard 353 Limit Controls
• CSA Class (321106) for industrial control equipment per CSA Standard C22.2 No. 14-M Industrial Control Equipment

Maximum Service Pressure:  250 PSI

Enclosure:      (Not for use in hazardous locations)

• NEMA Type 1 (For indoor use only)
• NEMA Type 4 (IFS-WPS only)  

Contacts:

• IFS-1/IFS-HC-1 Series:  One SPDT (Form C) switch
• IFS-WPS Series:  One SPDT (Form C) switch
• IFS-2/IFS-HC-2 Series:  Two sets of SPDT (Form C) switches to provide versatility in wiring two separate circuits.